Elektrine lite

← Feed

@yasar@thelemmy.club

2026-11-07 06:53 UTC

Fiber Optic and Photonics-Based AI Acceleration SIGNAL FLOW (BIDIRECTIONAL, 4-PORT): PC → 4 x QLE2660 HBA 16G FC PCIe ISP2722 Single-Port (in 14.025G mode; 2 forward + 2 reverse) → FC Frame (Port 0: Wpos phase, Port 1: Wneg phase — R4, 2 forward cards) → 2 x FTLF8529P4BCV 16G FC SFP+ 850nm MM (FORWARD) → 2 x 2 MM FBT Fiber Couplers (two 1x2 units, 4 outputs total) [Group A: VCSEL-1 P1+P2, Group B: VCSEL-2 P1+P2] → 2 x 6457567-4 or A14037-000 LC Duplex Adapters (Blue, Ceramic Sleeve, with SM05LC external threads) → Into S05LM56 socket → 2 x S5973 PIN Detectors (R4: dual parallel chains) → 2 x TLV3501 Comparators [threshold 0.15V] → (3.3V) → Level Shifter (1.8V) → 100nF AC → DS250DF410ABMR IN0_P/N, IN1_P/N → DS250DF410ABMR OUT0_P/N, OUT1_P/N → 100nF AC → OM4 LC-LC → 2 x FTLF8529P4BCV 16G FC SFP+ 850nm MM (REVERSE) → 2 x QLE2660 HBA 16G FC PCIe ISP2722 Single Port (in 14.025G mode, 2 cards for the return path) → PC DESCRIPTION: Since the QLE2660 is a single-port device, 4 cards are required to provide the necessary 4 ports. The previous assumption of 2x QLE2660 cards was based on a dual-port configuration; with the correction for single-port units, this has been updated to 4x QLE2660 cards. Forward path: QLE2660 #1 and #2 (2 ports) -> 2x FTLF8529P4BCV (forward) -> 2x2 FBT Return path: TLV3501 -> DS250DF410ABMR -> 2x FTLF8529P4BCV (return) -> QLE2660 #3 and #4 (2 ports) -> PC CALCULATION: Line rate per port is 14.025 Gbps; after 64b/66b encoding, the net rate is ~13.6 Gbps/port. With 4 cards, the total line rate is 56.1 Gbps, and the total data rate is ~54.4 Gbps. The forward path (2 ports) provides ~27.2 Gbps of data. A 67.19 MB file (537.5 Mbit) results in a forward transfer time of ~19.7 ms. LCM (Liquid Crystal Modulator) 4-step process takes ~80 ms. Optical VMM latency is in the ns range; TIA+TLV3501 latency is ~4.5 ns; the DS250DF410ABMR retimer latency is <100 ps; and the return path takes ~19.7 ms. Total time (optical + digital overhead) is <1–2 seconds, resulting in visual generation within a maximum of 3 seconds. BILL OF MATERIALS FINAL V4 (CURRENT): 4 x QLE2660 HBA 16G FC PCIe ISP2722 Single Port (in 14.025G mode) – 2 forward + 2 reverse 4 x FTLF8529P4BCV 16G FC SFP+ 850nm MM – 2 forward + 2 reverse 2 x 1x2 MM 50/125 3mm FBT FO Coupler 50/50 850nm (orange, without connectors) (2x2, 4 outputs total) 2 x 6457567-4 or A14037-000 LC Duplex Adapter with Blue Ceramic Sleeve (each with 2 LC ports, 4 LC ports total = 2x2 couplers) 2 x S05LM56 mount + 2 x SM05LC external-thread adapter 2 x S5973 PIN Photodiode + 2 x OPA858IDSGR TIA (Rf=1k, Cf=0.15pF) 2 x TLV3501 Comparator (threshold 0.15V) 1 x DS250DF410ABMR Retimer 25.8G 101-FCCSP 4-channel (2 channels active) NOTES: 6457567-4 is obsolete; use A14037-000 instead. Only 2 units of either are required. For the FBT coupler, do not use the yellow SM (single-mode) DWBC-1X2 type; use the orange MM (multimode) 50/50 850nm FBT coupler. - The DS125DF410 has a maximum capacity of 12.5G and therefore cannot operate at 16G; the DS250DF410ABMR supports 20.2752–25.8G (plus sub-rates) and is suitable for 14.025G, eliminating the need to downshift to 8G. The DS90UB953, being a 4.16G FPD-Link device, was incompatible with 16G FC; it has been replaced with the DS250DF410ABMR. This 4-port configuration meets the target of reducing the duration from 3 minutes (180 seconds) to a maximum of 3 seconds (~60x acceleration). DOI for project files doi.org/10.5281/zenodo.23930740

Replies (0)

No replies.